Artikel 121/449

 Zurück zur Artikelliste 

Daniel Defense MK18 .223 Rem 10,3"

€ 2.849,00 inkl. USt
Abhängig von der Lieferadresse kann die USt. an der Kasse variieren.

nicht lagernd - aktueller Preis kann variieren

Fabrikat: Daniel Defense
Modell: MK18 .223 Rem 10,3"
Kaliber: .223 Rem.
Waffenart: Selbstladebüchse
Lauflänge: 10,3"
Artikelnummer: 62934
 Vorbestellung 
Sie müssen angemeldet sein
um den Artikel vorbestellen zu können!









Use what “THEY” use.  The Daniel Defense MK18 features the railed forend Daniel Defense currently provides to USSOCOM and a 10.3” Cold Hammer Forged Barrel.  The MK18 Rail Interface System (RIS II) features the Bolt-Up System has been rigorously tested prior to fielding by USSOCOM.  The 10.3” barrel is the same length in use for the MK18 upper most commonly used for CQB operations.  The new independently ambi GRIP-N-RIP Charging Handle accommodates left- and right-handed shooters and is engineered for suppressed fire, with anti-gas features that redirect gas flow upward and away from the face and operator.  This rifle also comes with the rugged and comfortable Daniel Defense Buttstock and Pistol Grip.

NFA DISCLAIMER

This firearm is a regulated item by the National Firearms Act (NFA). Please check with your local and state municipalities for any further regulatory requirements. It is the buyer’s responsibility to make sure they comply with all NFA rules and applicable laws.

MATERIALS & CONSTRUCTION

  • LOWER RECEIVER: Mil-Spec with Enhanced Flared Magazine Well and Rear Receiver QD Swivel Attachment Point. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
  • UPPER RECEIVER: Mil-Spec with Indexing Marks and M4 Feed Ramps. CNC Machined of 7075-T6 Aluminum, Type III Hard Coat Anodized
  • BARREL: Chrome Moly Vanadium Steel, Cold Hammer Forged, 1:7 Twist, 10.3″ Govt Profile, Chrome Lined, Mil-Spec Heavy Phosphate Coated, and HP/MPI Tested
  • GAS SYSTEM: Pinned Low Profile Gas Block CNC Machined of 4140 hardened steel and Mil-Spec Heavy Phosphate Coating, Carbine Length, Direct Impingement
  • MUZZLE DEVICE: Daniel Defense Flash Suppressor, 17-4 PH Stainless Steel, Salt Bath Nitride Finished
  • BOLT CARRIER GROUP: M16 Profile, MP Tested, Chrome Lined, Properly Staked Gas Key
  • BUFFER: H Buffer
  • SIGHTS: Sold Separately
  • HANDGUARD: Daniel Defense MK18 RIS II, CNC Machined of 6061-T6 Aluminum, Type III Hard Coat Anodized
  • CHARGING HANDLE: GRIP-N-RIP Charging Handle, Body CNC Machined of 7076-T6 Aluminum, Handles & Latch CNC Machined of 6061-T6 Aluminum, Heavy Duty Stainless Steel Roll Pins, Type III Hard Coat Anodized
  • RECEIVER EXTENSION: 6 Position Mil-Spec 7075-T6 Aluminum
  • BUTTSTOCK: Daniel Defense Buttstock, Glass Filled Polymer with Soft Touch Overmolding
  • PISTOL GRIP: Daniel Defense Pistol Grip, Glass Filled Polymer with Soft Touch Overmolding
  • RAIL LADDERS: 3 low profile ladders made from Santoprene, heat resistant to 300° F.
  • Made in the USA!